Loading...
HomeMy WebLinkAboutSpecifications for Mobile Command Centermil LDV, Inc. I80 Industrial Drive Buffington, WI 53105 800.558.5986 Fax 262.763.0156 www.ldvusa.com VERY PRELIMINARY SPECIFICATIONS FOR: MIAMI POLICE DEPARTMENT MOBILE COMMAND CENTER LDV MODEL #MCC22 January 23, 2007 LD=+. ZDV. Inc. 1801ndus trial Drive �� Burlington, WI 53105 Elmo �' 800.558.5986 �� - Fax 262.763 0156 www.idvusa.com Section Qty 1.00 C■." ' :•' Du_► •►. 1.01 • Wheelbase of chassis: 218" • Overall length of apparatus, including rear step: 377" • Overall apparatus width, rub rail to rub rail: 96" • Rear step height from ground (loaded): 24"* • Overall height of apparatus (loaded): 144"* • Interior walkway height raw body: 83" • Interior walkway height finished: 81.5" • Interior walkway length: 264" • Interior raw body width: 93" • Interior finished body width: 85.5" * Estimated measurement dependent on chassis components, axles, tires, frame, suspension, and roof -mounted equipment. 2.00 CHASSIS: 2.01 • Freightliner MT-55 forward control chassis. 29,000-1b. GVWR minimun with rear air ride suspension and air brakes. ENGINE: • Cummins ISB-02 5.9 260 HP 2.02 CHASSIS WARRANTY: • Two (2)-year/24,000 mile Freightliner MT-55 chassis warranty. • Two (2)-year/unlimited miles Cummins engine warranty. • Three (3)-year/unlimited miles Allison transmission warranty. 2.03 1 Block heater shall be wired to a switch on the AC control panel. 2.04 1 DOT triangle reflector kit with three (3) triangles. 2.05 1 Pair of rubber wheel chocks with rope handle. 3.00 BODY; 3.01 1 • Load space area shall be 83" high x 93" wide x 22' long all aluminum step van body. 3,02 1 32" wide x 82" high 0.125" aluminum sedan door with 21.5" wide x 25.5" high fixed window and mini. blind. Door shall have continuous stainless steel piano hinge, two (2) nylon door straps and an aluminum drip rail. Located as shown on drawing. 3.03 1 Custom fabricated NFPA 1901 embossed 0.125" aluminum tread plate cover on rear bumper with radiused corners. 3.04 1 Custom fabricated 18 gauge stainless steel front bumper valance polished to a #8 finish. 3.05 3 Heavy-duty fluted aluminum grab handle with rubber inserts and chrome plated stanchions installed at exterior entry door location. 3.06 1 Heavy-duty fluted aluminum grab handle with rubber inserts and chrome plated stanchions installed inside entry door. 3.07 3 Whelen par 16 automatic courtesy LED at side entry door. LED # TOCACCCR Flange # TFLANGEC. 3.08 1 Courtesy Tight defeat switch on dash. 3.09 1 Kwikee Series 31 (or current model) 20" wide automatic electric steel entry step with NFPA 1901 approved embossed aluminum tread plate step cover. Product features: • Door switch extends step when door is opened, retracts step when door is closed. • Power switch locks step in extended position. • Ingnition override retracts step when ignition is turned on. • "Last out" feature extends step when the door is opened. Miami PD 22' 1-12-07 MRS.xls 1 1/12/2007 LOV LDV, Inc. 180 Industrial Drive Burlington, WI 53105 800.558.5986 Fox 262.763.0156 Section Qty 3.10 1 Kwikee Series 39 (or current model) 24" wide automatic electric steel entry step with NFPA 1901 approved embossed aluminum tread plate step cover. Product features: • Door switch extends step when door is opened, retracts step when door is closed. • Power switch locks step in extended position. • Ingnition override retracts step when ignition is turned on. • "Last out" feature extends step when the door is opened. 3.11 1 Trimark keyless entry with remote radio frequency (RF) transmitter fob, externally mounted keypad and lock actuator. 3.12 9 Trimark keyless entry, additional door acuator. 3.13 1 Trimark keyless entry, additional key fob. 3.14 1 Trimark keyless entry, additional exterior key -pad. 3.15 1 Whelen 810 Series combination stop/tail, turn and reverse lights, model number 8103RACR (or current model). 3.16 1 Entire underside of the apparatus shall be undercoated. Includes chassis, floor extrusions, step wells and aluminum compartments. 3.17 1 Rear mud flaps with anti -sail brackets. 4.00 LDV SLIDE -OUT: • Body shall have one (1) slide -out room with approximate dimensions of 78" high x 100" long x 30" deep. • The slide -out room shall be constructed of heavy duty tubular aluminum with welded joints for superior strength. • The sides of the room shall be sheeted with aluminum sanded and painted to match the exterior. • When in the closed position the slide -out room shall have a gap of less than .5" around the entire perimeter of the slide -out wall and the exterior side wall. • The slide -out shall incorporate a full perimeter air seal and wiper retainer to wipe debris from the room when sliding in and out. The structure around the air seal shall be reinforced to support the air seal. • Slide -out seal shall provide a weather tight seal without the use of an awning. • The drive mechanism shall utilize an electric screw drive with bearing follower and machined track for smooth operation. • Room shall be supported utilizing heavy-duty machined precision slides mounted off steel bearing plates that are attached to the frame rails using grade 8 bolts. • Use of floor rollers to support slide out is not acceptable, floor rollers cause deformation of body floor structure. • Slide -out shall not have any ceiling mounted components. • Controls for the slide -out shall utilize PLC logic and shall operate with the touch of one button. When the control button is pressed it shall automatically deflate the air seal, pause, vacuum out the air seal, extend the slide -out to its fully open position, and re -inflate the air seal. An LCD display shall be provided on the control pad and shall be capable of displaying status information on the slide -out operation to the user. • Slide -out shall be finished in such a fashion that will allow access to serviceable components under the floor of the body. All serviceable components shall be protected from the elements. 5.00 PAINT AND GRAPHICS; 5.01 Body base color shall be Dupont Imron N0006-HH white (or equal). 5.02 1 4-inch wide reflective stripe on the exterior back and sides of the vehicle, piacea up to round level color — to be determined Miami PD 22' 1-12-07 MRS.xls 2 1 /12/2007 1 LDV, fnc. ��. 1801ndusfria! Drive ��� Burlington, WI 53105 �upj 800.558.598b Fax 262./63.0 f 56 .��► Fax www.ldvusa.cam Section Qty 5.03 1 Custom computer -generated non -reflective vinyl graphics per customer specifications. Includes up to seventy 8"-10" letters and up to forty-five 3"-6" letters. All lettering shall be shaded or outlined (colors/style — to be determined). Note: Graphics package does not include production of custom shields and/or seals. HERITAGE ONYX INTERIOR: 6.00 • Wall Covering: #D487-07 Pearl Silver Laminate available in #D354-01 White Dry Erase Laminate on request • Ceiling Fabric: Excalibur Chrome • Floor Covering: #150 Onyx PVC Flooring • Office Chairs: Charcoal • Vinyl Coverings: #CB-11 Naugahyde NaugaSylk Black Magic • Cabinets: #EBT-2-2002 Black Powder Coated Aluminum available in RAL-7035 Grey on request • Counters and Tables: #9091-ML Midnight Melange Solid Surface Note: LDV, Inc. reserves the right to substitute equivalent materials. 7.00 DRIVER/PASSENGER CAB AREA: _ 7.01 • Cover cab doors with aluminum panels upper half to be wrapped with vinyl and lower half to be wrapped with padded vinyl. • 10" high 0.100" bright aluminum tread plate kick plate at bottom of doors. • Heavy-duty rubber grab handle on each door. • 1/2" plywood panels covered with vinyl above driver and passenger doors. • Cab sub ceiling shall be 1/2" plywood. • Cover sub ceiling with Veelok Oxford 17-oz. ribbed loop pile fabric. • Vehicle height sign on dash. • Cab floor shall be covered with 5/8" plywood and covered with flooring as specified in Walls, Ceiling and Floor section. • Insulated black rubber mat in driver and passenger toe plate area. Insulate walls in toe plate area and install vinyl covered panels. • Vehicle shall have a Final Stage Vehicle Certification and Altered Vehicle Certification as required by Federal Motor Vehicle Safety Standards (FMVSS) 49 CFR Part 567.5 and 567.7 • Payload sticker in cab area with vehicle axle load ratings and available axle payload as built. 7.02 1 Work area on passenger side constructed of 5/8" plywood covered to match rear counter -tops and trimmed with vinyl T-molding. 7.03 1 Control panels for 120Vac and 12Vdc systems shall be located in the overhead console. The entire console shall be constructed of 3/4" plywood. The face shall be finished with black laminate and the bottom shall be covered with vinyl. 7.04 1 Red LED/Clear incandescent dome light with 3-position switch, red/off/white. 7.05 1 Pair of 6" front windshield fans. Miami PD 22' 1-12-07 MRS,xls 3 1/12/2007 LD=, LDV, Inc. 180 Industrial Drive 53106 �-� Burlington, WI 53105 f�.' 80Q.5I .�WM/� Fax 262,763.0 156 www.ldvusa,com Section Qty 7.06 1 Weldex WDRV-6800M (or current model) 6.8" color LCD back-up monitoring system. Camera features: • 1/3" Color Camera With Infra -Red LEDs • Weather Proof Camera Enclosure • 380 Lines of Resolution • 1.0 LUX (IR LED Off) / 0 Lux (IR LED On) Minimum Illumination Monitor features: • High -Resolution 6.8" TFT LCD Monitor • 6.8 inch Picture Measured Diagonally • 3 Camera Inputs • Auto -Power On • Dimensions: 6.53"(W) X 5.55"(H) X 1.16"(D) 7.07 1 Pioneer DEH-P4700MP (or current model) MOSFET 50-watt x 4, CDIMP3IWMANVAV Receiver with 3-band parametric EQ, and one (1) pair of Pioneer TS-A6970R (or current model) 6" x 9" three- way speakers. 7.08 1 Pair of Pioneer TS-A6970R (or current model) 6" x 9" three-way speakers. 7.09 1 L-pad volume control for additional speakers. 7.10 1 Blackout curtains for all cab area windows: • Custom fit to cab windows. • Curtains shall be made of black woven fabric made of 100% SEFIFR® self -extinguishing fibers, modacrylic solution dyed with a fluorocarbon finish, available in grey on request. • Weight is approximately 9.25-oz. per square yard. • Material shall be guaranteed not to fade, mildew or rot for 5 years. • Seams shall be double stitch/single fold with 1" sewn -in hook -and -loop or nickel plated fasteners. • Fabric shall meet FMVSS 571.302 requirements for use in the driver/passenger area. 8.00 WALLS, CEILING AND FLOOR: 8.01 Cover interior body side beams with 12mm LITE PIy® plywood sub wall. Product features: • Extremely light weight - up to 30% lighter than standard plywood • 7 ply construction • Low formaldehyde emissions (E-1 classification) 8.02 Cover sub wall with Wilsonart laminate. 8.03 Radius contoured walls in rear conference area 8.04 Cover interior roof beams with 9mm LITE Ply® plywood sub wall. Product features: • Extremely Tight weight - up to 30% lighter than standard plywood • 7 ply construction 8.05 Cover sub ceiling with Veelok 17-oz. ribbed loop pile fabric. 8.06 5/8" exterior grade tongue & groove plywood underlayment for floor, ICI 7-2-7-2 G-1 Exposure 1- APA 347 PCUF PSI-95 (or equivalent). 8.07 Lonseal Loncoin II Flecks 150 Onyx non-skid commercial grade PVC flooring. The flooring shall be a continuous p ece from front to back. 8.08 2-1/2" vinyl cove molding as required (mop board). 8.09 2 30" laminate covered pocket door installed on heavy-duty aluminum track with two (2) four-wheel roller trucks. Pocket door shall have recessed handles and a key lock. 8.10 All bulkheads shall be covered with Wilsonart laminate. 8.11 1 Cover load space door with black powder coated aluminum panel, install 10" high 0.100" bright aluminum tread plate kick plate at bottom of door and heavy-duty rubber grab handle. Miami PD 22' 1-12-07 MRS.xIs 4 1/12/2007 LDma+. r 1-DV, Inc. 180 Industrial Drive �1♦� Burlington, Wf 53105 i1• �' 800.558.5986 �et�r- Fax 262,763.0I56 www.ldvusa.com Section Qty 8,12 1 30" wide x 12" high flush mount deep -tint horizontal sliding window with mini -blind, located as shown on drawing. Window features: • Black baked aluminum frame construction • Unique Flush Mount frame offers automotive style frameless appearance • Hidden water drainage system • Windows have 2.5" radius corners (3.25" on Egress models) • Glass is tempered with 31 % light transmission • All glazing materials are DOT approved • 2-piece clamp ring installation allows for easy replacement in the event of breakage • Sliding screen for exterior access. 8.13 1 36" wide x 24" high flush mount deep -tint horizontal sliding egress window with mini -blind, located as shown on drawing. Window features: • Black baked aluminum frame construction • Unique Flush Mount frame offers automotive style frameless appearance • Hidden water drainage system • Windows have 2.5" radius comers (3.25" on Egress models) • Glass is tempered with 31% light transmission • All glazing materials are DOT approved • 2-piece clamp ring installation allows for easy replacement in the event of breakage • Fixed screen. 9.00 SEATING: 9.01 4 Herman Miller Aeron A7; 112AWB (or current model) ergonomic work chair. Product features: • Standard height range pneumatic height adjustment • Tilt limiter • Fully adjustable arms • Nonupholstered armpads • Chair size B • Adjustable lumbar support • C7 2.5" double wheel caster • Pellicle classic carbon (charcoal color) 9.02 2 Custom fabricated sliding pedestal for desk chair. Located as shown on drawing. 9.03 Fabricate and install fixed bench seating with removable cushions as shown on drawing. Bench seat cushions shall be covered in heavy-duty vinyl. 9.04 BENCH SEAT REQUIREMENTS: • Foam for seat backs and bottoms shall have a minimum density rating of 28, a minimum compression rating of 65 and a support factor of 2.2. • All bench seating material must meet Federal Motor Vehicle Safety Standards part 571.302 Flammability of Interior Materials. • Seam stitching shall be done with 8-oz. bonded nylon thread. • Material corners shall be squared or angled to fit precise cut of foam. • Foam shall be bonded to plywood backer with industrial grade elastomer adhesive. • Bottom and sides of plywood backer shall be completely sanded. • Stapling of fabric/vinyl to backer with industrial grade upholstery staples. • No more than a 112" space is acceptable between staples around the entire perimeter. • Ali fabric shall be stain resistant. 10.00 CABINETS: Miami PD 22' 1-12-07 MRS.xls 5 1/12/2007 LD LDV, inc. =j 180 industrial Drive MEM �� Burlington, Wf 53105 �' 800.558, 5986 r�� �� Fax 262.763.0I 56 www.ldvusa.com Section Qty 10.01 Custom fabricated aluminum cabinets located as shown on drawing. Cabinet specifications: • Base cabinets constructed of 0.080" powder coated aluminum with anodized aluminum frames. • Base cabinet doors are double shell, formed from a single sheet of 0.080" aluminum, with a 0.040" aluminum door back attached. • Overhead cabinets constructed of 0.064"powder coated aluminum with anodized aluminum frames. • Overhead cabinets doors are double shell, formed from a single sheet of 0.064" aluminum, with a 0.040" aluminum door back attached. • Overhead cabinets doors swing up on a full-length aluminum hinge, and are held open with a locking door stay. • Overhead cabinets to have one adjustable shelf per door (24" high and taller cabinets only) - locked in place to your selected height. Shelves are formed from a single sheet of 0,064" mill finish aluminum, with 1 1/8" hemmed edges. 10.02 Radius edging incorporated as design permits. 10.03 4 Dry erase writing surface on overhead cabinet door. 10.04 6 Gas shock lift supports on overhead cabinet door. 10.05 5 Halogen puck light under overhead cabinet. 10.06 Wllsonarf Gibraltar 1/2" solid surface countertop over subsurface, Solid surface countertop shall have a 1-1/2" front lip with radius edge. 10.07 WI!sonari Gibraltar 1/2" solid surface conference tabletop over subsurface. Solid surface countertop shall have a 1-112" front lip with radius edge. 10.08 Powder coated 0.125" aluminum conference table base with radius end caps. 10.09 Solid Surface communication equipment shelf mounted above countertop. 10,10 Custom fabricated black laminate covered rack cabinet from counter top to ceiling with rack rails on two sides. Located as shown on drawing. 10.11 4 Aluminum framed dry erase marker board with pin strip. Sized and located as shown on drawing. 10.12 4 Pencil drawer under countertop, located as shown on drawing. 10.13 1 Computer cable pass-thru grommet in counter. 11.00 HVAC SYSTEM: 11.01 1 Fan-tastic Vent model 4000 R (or current model) 3-speed reversible 12" power roof ventilator. 11.02 3 Ducted Coleman Polar Mach 9200 series low profile air conditioner with wall mounted thermostat. Includes: • 9223-C876 13,500 nominal BTU air conditioner with condensate pump. • 83300635 Chill Grille Assembly with 5,600 BTU heat strip • 8330-3362 Thermostat • Aluminum Air Duct, internally mounted in ceiling • 22120010 Louvered Ceiling Vents, as required 12.00 120/240VAC ELECTRJCAL SYSTEM: 12.01 1 Onan Commercial Quiet Diesel 12-kW generator model 12.0HDKCD-2209 (or current model) mounted in custom fabricated all aluminum compartment. Generator has the following features: • 69 dB(A) © full load measured at 10 feet. • Voltage regulation no-load to full -load: +l-1 % • Frequency regulation no-load to full -load: +1- 0.1% • Random frequency variation for constant load: +1- 0.5% • Random voltage variation for constant load: +1-1 % Miami PD 22' 1-12-07 MRS.xls 6 1 /12/2007 LO180 r LDV, Inc, Industrial Drive MOMAMS�1� Burlington, WI 53105 ...., ill . 800.558,5986 .�� Fax 262.763.0156 www.rdvusa.com Section Qty Compartment shall be constructed to the following specifications: • Compartment shall be constructed from 0.187" aluminum with all welded seams. • Compartment shall have 0.125" aluminum 2" box pan doors and 0.125" aluminum frames. • Door frames shall be riveted to the body and welded to the compartments. • Doors shall have stainless steel hinges attached to the doors and door frames with stainless machine screws. • Doors shall have slam latches and flush mounted handles. • Doors shall have 0.100" aluminum treadplate panels on interior surfaces. • Doors shall be held open in a 90° position with gas charged lift/support cylinders. • Doors shall be sealed with industrial grade neoprene gasket. • Compartment shall have internal lighting when door is open. 12,02 1 Generator exhaust routed to roof. 12.03 Intermatic LH Series IG1201LH (or current model) hardwired Surge Suppression System: • All mode Protection (L-N, L-G, NI-G, L-L) • 200 KAIC Surge Rated Fuses • Thermally Protected MOVs for maximum safety • Fault Current Tested to 200 kAIC • EMI/RFI Filtration — 20 to 30 dB from 20 kHz to 100 MHz • UL1449, 2nd Edition, cULus • Nema 12 Style Enclosure • 10 year product warranty • Pre -wired with 30" of #10 AWG wire leads • LED Indicator Lights • lntermatic Thermal Monitoring System • 7.5"H x 4.25"W x 4.0"D • 5.5 lbs. 12.04 1 50A-120/240Vac control panel with generator and shore power main breaker, twelve (12) UL listed magnetic/hydraulic branch circuit breakers with amber LED indicators, digital voltmeter, digital frequency meter, digital ammeter, generator stop/start switch, generator hour meter, shore power reverse polarity indicator and 3-position rotary transfer switch. 12.05 120Vac auxiliary control panels as required with UL listed magnetic/hydraulic circuit breakers and amber LED indicators. 12.06 1 Kussmaul Auto Eject 20, 20A-120Vac shore power inlet with 25-ft. 20A-120Vac shore power cord. 12.07 1 Marinco 50A-125/250Vac waterproof shore power inlet, 50-ft. 50A-125/250Vac shore power cord and 6-ft. 50A-125/250Vac pigtail. 12.08 8 Specification grade 20A-125Vac duplex receptacle mounted in stainless steel wall plate or raceway panel, located as shown on drawing. Receptacle is not dedicated to any installed equipment. 12.09 4 Specification grade 20A-125Vac exterior GFCI duplex receptacle with weatherproof PVC cover. GFCI receptacles will be wired in pairs to 20A circuit breakers located in the 120Vac electrical load distribution center. MIaml PD 22' 1-12-07 MRS.xls 7 1/12/2007 LD_�. LDV, inc. 180 fndustrla! Drive ��1 Burlington, WI 53105 �' 800.558,5986 �� �� Fax 262,763,0156 www.lcIvusa.com Section Qty 12.10 Wire chase wire management raceway system located as shown on drawing. Product features: • Satin anodized finish. The finish resists rust, corrosion and fading. Material extruded from 6063-T5 aluminum alloy. • Removable dual cover. Makes wiring easy and accessible and provides maximum flexibility for adding or relocating outlets and circuits. The cover retention is 45 lbs. straight pull for one minute. • UL Listed multioutlet assemblies. File E68073 Guide PVGT, Fittings: File E121188 Guide RJPR. Meets Article 380 of NEC and meets Section 12-3032 of CEC. • UL and cUL Listed component raceways. File E73943 Guide RJBT, Fittings: File E74343 Guide RJPR. Meets Article 386 of NEC and meets Section 12-600 of CEC. • UL5 and ADA compliant. Raceway and fittings meet UL5 specifications and can be installed in conformance with ADA requirements 12.11 1 Will -Burt Night Scan Powerlight NS15-3600M (or current model) 240Vac Tight tower with dual tilt. Includes: • Four (4) 900 watt Magnafire 3000 Halogen I.R. lightheads. • Dual tilt remote control positioner (control box for positioner shall be installed in an under body storage compartment, if one is not available control will be mounted in a Cast Products, model FT41501, cast aluminum box). • Look -up light for added safety. • Dash mounted warning light with interlock to prevent vehicle from being moved with light tower raised. • Additional roof support structure, as required. 12.12 1201240VAC WIRING REQUIREMENTS: • All 120/240Vac main wiring shall be stranded THHN wire and run in non-metallic Carlon Carflex liquid tight conduit. • All 120/240Vac branch circuit wiring shall be stranded THHN wire (AWG 12 minimum) and run in non-metallic Carlon Carflex liquid tight and Canon Flex -Plus blue ENT conduit. • All electrical circuits and appliances shall conform to applicable national electrical codes. 13.00 C LC C LSYT 13.01 • Six (6) Lifeline GPL-4C 6Vdc Absorbed Glass Mat (AGM) batteries. Batteries shall be installed underbody in slide out weather resistant aluminum compartment. Compartment shall have box pan door with slam latch, flush mount handle, key lock and Kwikee heavy-duty slide assembly. Four (4) batteries will be separated for auxiliary equipment and two (2) batteries will be for communications equipment. • Three (3) electronic converter/chargers, 80 amp minimum output each installed underbody in weather resistant aluminum compartment. Converter/charger features: • Charges three banks of batteries at the same time. • UL listed for safety. • Manual reset circuit breaker. • Reverse battery protection. • Electronic current limiting. • High voltage protection. • One (1) master disconnect switch to control the auxiliary battery systems. • 12Vdc control panel with seven (7) UL listed magnetic/hydraulic circuit breakers with red LED indicators, 12Vdc digital voltmeter, and 12Vdc low voltage alarm. • 12Vdc auxiliary panels with UL listed magneticlhydraulic circuit breakers as required. • 12Vdc auxiliary digital voltmeter to monitor the communications battery system. 13.02 20 Thin-Lite model 616 18" white 12Vdc fluorescent light fixtures located as shown on drawing. 13.03 7 Thin-Lite model 616 18" blue 12Vdc fluorescent light fixtures located as shown on drawing. Miami PD 22' 1-12-07 MRS,xls 8 1/12/2007 LD LDV, Inc, ��. 1801nclustrial Drive �' Burlington, WI 53105 �' 800.558.5986 v��� Fax 262.763.0156 www.lclvusa.com Section Qty 13.04 8 Whelen 810 Series white quartz halogen scene light with 8-32° optics, model number 810CAOZR (or current model). 13.05 4 Whelen 508 Series low level perimeter scene Tight with 8-32° optics, model number 580CAAZR (or current model). 13.06 7 15A-12Vdc power outlet mounted in stainless steel wall plate or raceway panel, located as shown on drawing. 13.07 2 Streamllght "Light Box" model 45102 (or current model) truck mount 12Vdc direct wire Tight. 13.08 1 Whelen 295HFS2 (or current model) remote siren amplifier with flush mount control head. 13.09 1 Whelen SA3146 (or current mode!) high performance, multi -port 100 watt speaker with SACSTFMP (or current mode!) polished flange casting for bumper mount. _ 14.00 12VDC EMERGENCY LIGHTING: 14.01 1 Whelen L31 HGF (or current model) green LED command beacon mounted on roof or antenna 14.02 1 Whelen Freedom Series LED Tight bar FL2RRBB (or current model) mounted above windshield on custom fabricated 0.125" aluminum bracket painted to match body. Includes: • 1 - 9LLTH72 Custom 72" length • 3 - FLDRB 400 Series Linear LED Flashers (red street side/blue curb side) • 1 - FLDRR 400 Series Linear LED Flashers (red street side/blue curb side) • 1 - FLDSCBL Cable Exit on Driver Side Note. Install weather-proof connector and Tight bar cable in bracket channel. 14.03 2 Whelen PLAST4V (or current model) polished chrome vertical housings for four 600 series lightheads. 14.04 2 Whelen 600 series LED amber turn signal light heads with populated arrow shape and multiple flash patterns, model number 60AOOTAR (or current model). 14.05 2 Whelen 600 series rnax intensity LED brake/tail light heads, model number 60ROOXRR (or current model). 14.06 2 Whelen 600 series halogen Back-up Tight heads, model number 60J000C11(or current model). 14.07 1 Whelen 600 series Super -LED Iighthead with internal flasher, red LED's with clear outer lens, model 6OR02FCR (or current model). Includes chrome flange 6EFLANGE (or current model). Located as shown on drawing. 14.08 1 Whelen 600 series Super -LED Iighthead with internal flasher, blue LED's with clear outer lens, model 60BO2FCR (or current model). Includes chrome flange 6EFLANGE (or current model). Located as shown on drawing. 14.09 4 Whelen 700 series Super -LED lighthead with internal flasher, red LED's with clear outer Tens, model 7ORO2FCR (or current model). Includes chrome flange 7EFLANGE (or current model). Located as shown on drawing. 14.10 4 Whelen 700 series Super -LED Iighthead with internal flasher, blue LED's with clear outer Tens, model 7OBO2FCR (or current model). Includes chrome flange 7EFLANGE (or current model). Located as shown on drawing. 14.11 3 Whelen 900 series Super -LED Iighthead with internal flasher, red LED's with clear outer lens, model 9ORR5FCR (or current model). Includes chrome flange 9OFLANGC (or current model). Located as shown on drawing. 14.12 3 Whelen 900 series Super -LED lighthead with internal flasher, blue LED's with clear outer lens, model 9OBB5FCR (or current model). Includes chrome flange 90FLANGC (or current model). Located as shown on drawing. Miami PE) 22' 1-12-07 MRS.xls 9 1 /12/2007 �� ♦1,131 � ap MEI xi LDV, Inc. 180 Industrial Drive Burlington, Wl 53105 800,558.5986 Fax 262,763.0156 www,Idvusa.com Section 14.13 15.00 15.01 15.02 15.03 Qty 12VDC WIRING REQUIREMENTS: • 2-gauge minimum copper stranded battery cable shall be used for 12Vdc main supply lines. All cable runs shall be full length, no splices. All cable terminals shall be staked and soldered. All cable shall be enclosed in convoluted polyethylene tubing and the ends of the cable shall be sealed with color -coded shrink-wrap identifying the function of the cable. • All added electrical circuits shall be protected from over -current by resettable circuit breakers appropriately rated for the load. Only circuit breakers shall be used in the installation of added electrical wiring (plug type fuses are unacceptable). • Circuit breaker functions shall be identified by engraved or printed labels. • All added wiring for load runs shall be AWG 8, 10, 12, 14 and 18 and must conform to MIL-W- 16878F. • Wire terminals for added circuits must conform to MIL-T-7928. Terminals shall be insulated, insulation grip, TYPE II, CLASS 2 and shall be crimped with tooling recommended by the terminal manufacturer. • All wiring shall be numbered or lettered on 6" centers minimum. • Wiring shall be protected from chafing and abrasion with convoluted polyethylene tubing (wire loom) as required. • Where wire passes through sheet metal, bulkheads and structural supports, plastic grommets shall be used to protect both wiring and wire looms. • All wiring shall be supported on 12" centers. • All wire bundles shall be tied with trimmed nylon ties on 6" centers minimum. • The complete 12Vdc wiring system and electrical appliances shall be to modern automotive standards throughout the installation. • Extreme care shall be exercised to provide for easy serviceability of the system in future years. • Extreme care must be taken in the installation to avoid the engine manifold, engine exhaust, and muffler, which could expose the wiring to severe overheating during long periods of operation. Proper insulation and heat deflection panels must be installed in such areas. • A high -current 12Vdc system wiring schematic shall be provided. • These are the minimum acceptable 12Vdc wiring requirements. AUDIONIDEO: Weldex 7" Color LCD Monitor WERV-7043M (or current model). LG 17" Multi -Media LCD Monitor/TV M1717A-SM (or current model) with custom fabricated bracket to enable monitor to be mounted on vesa bracket. Product features: • Maximum resolution: 1280x1024 • 17" display with 170° horizontal and 170° vertical viewing angle • 16.2 million colors • TV tuner • Brightness: 300 cdlm2 • Dimensions: 15.25"W x 14.75"H x 2.5"D Sharp AQUOSTA° LC15S5U (or current model) 15" LCD TV. Product features: • Aspect Ratio: 4:3 • 15" display with 170° horizontal and 170° vertical viewing angle • High Brightness: 430 cd/m2 • 500:1 Contrast Ratio • 60,000-Hour Lamp Life • Dimensions: 14.625"W x 13 1/2"H x 4"D Miami PD 22' 1-12-07 MRS.xls 10 1/12/2007 LDV, Inc. LD180Industt Drive MEN:' Burlington, WI 53105 V 800.558,5986 �ommi� Fax 262.763.0156 www.ldvusa.com Section Qty 15.04 2 Sharp AQUOSTM LC20E1 US (or current model) 20" ASV (Advanced Super View) LCD Panel. Product features: • High Brightness (430 cd/m2). • 170° horizontal and 170° vertical viewing angle. • 1 RCA composite video input, 1 S-video mini -din input and 1 Y/Pr/Pb component input. • Electronic PLL tuner. • NTSC/PAL/SECAM video system. 15.05 8 Vesa-standard 75 mm wall mount with quick -release. 15.06 1 Marshall Electronics V-LCD20 (or current model) 20" active matrix color LCD panel with TV tuner viewable from the curbside exterior, under awning. Product features: • Ultra bright — 450cd. • 20.1" display (viewing area). • 8-bit color with 640 x 480 resolution. • 181 channel, cable -ready TV tuner. • Dimensions: 20" W x 17" H x 2.5"D. 15.07 1 Mount for exterior viewable LCD monitor. Includes: • Low-e glass. • Flush mounted weatherproof speakers. • Speaker amplifier. 15.08 1 Weatherproof exterior door to access rack mounted audio/video/telephone equipment. Door to be constructed from 0.125" aluminum with all welded seams and will be hinged at the bottom to provide a work surface when open. Includes locking latch and Whelen #PSCABCCR LED compartment light with automatic switch. 15.09 2 Sony RDR-VX515 (or current model) DVD-RNHS Combination Unit. Product features: • DVD+RWI+R, DVD-RW/-R Recording Compatibility. DVD+RW/+R, DVD-RW/-R and CD-R/RW playback may not be compatible with all discs, depending on recording conditions. • One Button Dubbing from VCR to DVD or DVD to VCR (non copy written material only). • Variable Bit Rate Recording (at HSPISPILP/EP/SLP). • 4 Video Head Stereo VHS with 19 Micron Heads. • VHS & S-VHS (SQPB) Playback. 15.10 1 Sony RDR-HX715 (or current model) DVD recorder with 160GB hard disk drive. Product features: • DVD+RWI+R, DVD-RWI-R DVD recording compatibility. DVD+RW/+R, DVD-RW/-R and CD- R/RW playback may not be compatible with all discs, depending on recording conditions. • Dynamic VBR High Quality Dubbing from Hard Disk Drive to DVD. • Up to 64 times High Speed Dubbing from Hard Disk Drive to DVD. • HQ+, the Optimum Bit Rate Recording on Hard Disk Drive for Superior Picture Quality. • Built in Television Tuner. 15.11 1 MotoSat DataStorm F1 (or current model) .74 meter mobile internet satellite system with optional dual LNB for DirecTV television reception. Product features: • Download speed of 700 to 1,500kbps. • Upload speeds between 30 to 90kbps. • Automatic pointing to the DirecWay Satellite. • Auto stow if the vehicle is moved. • Auto stow if the vehicle rocks due to wind. • System router. _ Twelve (12) months MotoSat DataStorm standard two-way internet satellite system service. _ 15.12 1 Channel Master model 6314IFD (or current model) active multi -switch. 15.13 4 DirecTV D11 (or current make/model) DSS receiver. UL and FCC approved. Mlami PR 22' 1-12-07 MRS.xls 11 1 /12/2007 1 LD.=. LDV, Inc. 180 Industrial Drive �� Burlington, WI 53105 �, 800.558,5986 ��- Fax 262.763.0 156 Vwww.ldvusa.com Section Qty 15.14 6 Middle Atlantic rack mount kit (custom fitted for VCRs, DVD players, VCR/DVD combination units, and DSS receivers). 15.15 1 Sony UP-20 (or current model) A6 color video printer with UPC-21 L - L size standard color print pack (4 x 50 packs) (5 in. x 3.6 in.). Product features: • 400 dpi resolution. • 4 frame memory. • Analog video inputs and outputs. • RS-232C interface. • Monitor loop -through. 15.16 1 Everfocus color camera and Louroe #ASK-4 (or current make/model) audio/video surveillance kit in the conference area interfaced to the vehicle video system and routed to a VCR to record. Note: Install power switch in conference area for camera and microphone. 15.17 2 Exterior audio/video input (RCA audio jacks, BNC video jack). 15.18 1 Winegard MA1000W (or current model) motorized Sensar amplified directional TV antenna. Includes: • Antenna amplifier. • Control panel to raise, rotate, and auto stow the antenna. • Dash mounted warning light with interlock to prevent moving the vehicle with antenna raised. 15.19 1 CATV inlet interfaced to modulated video system or TVNCR. 15.20 1 NB switch to select antenna or CATV. 15.21 1 Pelco QD104C Digital Quad Video Processor with RK 100 rack mount kit. Product features: • Real-time quad video • Quad Monitor Output that displays full -screen or quad image • Sequencing of full -screen and quad views 15.22 Modulated audio/video system to enable any audio/video source (i.e. camera, VCR, DVD player, DSS receiver) and up to four local off -air channels to be viewed on designated TV channels. Includes: 15.23 2 HE Series modulated headend audio/video system 12 space rack LDV 19180062 (or current model) with LDV 19180063 (or current model) power supply. 15.24 15 HE Series fixed modulator. Modulators will start with channel 2 and will ascend accordingly to reach quantity specified. 15.25 4 HE Series agile demodulator LDV 19180065 (or current model). 15.26 2 HE Series 12 position Passive Combiner LDV 19180066 (or current model). 15.27 15.28 1 HE Series 16 position Passive Combiner LDV 19180067 (or current model). All RF cable for DSS antenna systems (when specified) shall be Belden #9116 series 6 broadband coaxial cable. All other video cabling shall be Belden #1505A RG-59/U precision video cable. 16.00 MAST AND MAST MOUNTEDIQ 1PMENL: Miami PD 22' 1-12-07 MRS.xls 12 1r12r2007 , LD , LDV, Inc. ANN=, 180 Industrial give �' Burlington, Wf 53105 iiiiii N �% 800.558.5986 op! W. Fax 262.763,0156 www.ldvusa.com Section Qtt 16.01 1 Will -Burt TMD6-25-368 (or current model) 25-ft. heavy-duty non -locking telescoping pneumatic mast. Mast features: • 150 Ib. payload capacity (including Nycoil) • 25' extended height • 5' 10" nested height Includes: • Airmaster Control with airline filter, lubricator, regulator, control valve and dump valve. • 40' of Nycoil conduit and weather -tight fittings. • Will -Burt external mount shelf bracket and external mount support bracket. • Will -Burt magnetic mast extension warning kit with warning light at mast control location and driver location. • Interlock to prevent vehicle from being driven with mast raised. 16.02 1 Thomas Ultra Air-Pac 1/2-hp compressor with 2 gallon air tank. 16.03 1 Custom fabricated 0.125" aluminum Nycoil cylinder painted to match body color. 16.04 1 Custom fabricated 0.125" aluminum mast cover painted to match body color. 16.05 1 Will -Burt D-TEC mast safety system mounted on mast. System features: • High voltage sensor aides operator in detecting overhead power lines. • Anti -collision sensor automatically stops mast extension, assisting operator in detecting overhead obstructions. • Tilt sensor ensures that vehicle is level and D-TEC is pointing directly upward prior to mast extension. • 35 watt quartz halogen look -up spot light to illuminate area directly above mast. 16.06 1 Camera system installed on mast. Includes: • One (1) Pelco PT57024P (or current model) medium -duty pan & tilt. • One (1) Pelco MPTAZ24DT (or current model) combination pan, tilt, zoom controller with rack mount kit. • One (1) Pelco EH4722-2 (or current model) 22" outdoor camera enclosure with heater and blower. • One (1) Altronix T24130 (or current model) 24Vac 1100VA transformer. • One (1) lkegami ICD-870-24 (or current model) 1/3" CCD ultra -high performance color video camera requiring a minimum object illumination of 0.1-Iux/F1.4. • One (1) Pelco 13ZD5.5X30 (or current model) 1/3" CS mount CCD lens with a 30X f1.8 lens range from 5.5 to 165-mm. 17.00 RADIQi 17.01 Primary 12Vdc power leads for communications radios shall be minimum 2-gauge copper stranded wire with soldered crimp -on end connectors (gauge based on radio requirements). Cables shall be enclosed in convoluted tubing and function identified with colored shrink-wrap. Power to radios shall be controlled by a continuous -duty switch actuated by the auxiliary battery disconnect switch. 17.02 10 Prewire and make installation provisions for communications radio. Installation includes: • NMO-style base on the roof or antenna raceway, as applicable. • LMR195 antenna cable routed to radio transceiver location in Carlon Carflex ENT conduit. • 12Vdc power routed to radio transceiver location. Miami PD 22' 1-12-07 MRS.xis 13 1/12/2007 mni lr1 L jail .‘111=Fr- LDV, Inc. 180 Industrial Drive Buffington, WI 53105 800,558.5986 Fax 262.763.0156 www.ldvusa.com Section 17.03 17.04 17.05 1 18.09 18.10 18.11 19.00 19.01 19.02 Qty 10 Customer supplied radios and locations: Cab Area • Qty. - Make/Model, Freq/Power Out/Trunk or Dash Mounted A COIM,'UTER NEIWCARKANCLEGIUIPME 1 RJ-45 CAT6 computer network jack with CAT6 cable routed through Carlon Flex -Plus ENT conduit or raceway (as applicable). Leviton 69586-U12 (or current model) 12-port Cat6 rack mount patch panel. Miami PD 22' 1-12-07 MRS.xls 14 1/12/2007 L.� 0 LDV, Inc. ANL +. 180 Industrial Drive eme nem �� Burlington, W! 53105 �' 800.558.5986 �- Fox 262.763.0/56 www.ldvusa.com Section Qty 19.03 1 Allied Telesyn AT-GS900116-10 (or current model) 16-port 10/100/1000T Unmanaged Gigabit Switch. Product features: • Wirespeed performance • Auto -negotiation Gigabit ports • Auto MDIIMDIX on TX ports • Transparent to VLAN packets . • Full duplex flow control 19.04 9 Certified 18" CAT6 patch cord. 19.05 1 Certified 36" CAT6 patch cord. 19.06 1 Cable Certification Report confirming that network wiring complies with CAT6 specifications. 19.07 1 HP LaserJet 3015 (or current model) all -in -one printer, fax, copier, and color scanner with HP Jetdirect J6035C#ABA (or current model) 175x print server (10/100 Base -TX) and dedicated C.O. input in landline input box. Note: Fax feature is only available when a C.O. line is connected to the vehicle. 20.00 JIi1ISCELLANEOUS ELECTRONICS: 20.01 1 Napco Gemini alarm system. System includes magnetic contacts on all entry doors, exterior storage compartment doors, battery box doors, generator compartment doors and hood. Two (2) key fobs, key pad, 360° ceiling mounted motion sensors, siren and bell. Note: If applicable, one (1) Telular Phonecell will be interfaced to the alarm system to allow the customer to program a telephone number that will be dialed automatically if the alarm system is triggered. Phonecell will be connected to a constant hot power source. 20.02 1 Columbia Weather Systems Capricorn 2000TM rack mounted weather station, 8150-LDV-2 (or current model), with LCD touch screen display. System includes the following: • Barometric pressure sensor. • Wind speed and direction sensor assembly. • Removable two-piece 12' overall height aluminum mast for wind speed and direction sensor assembly. • Interior and exterior temperature probe. • Relative humidity probe. • Self -Aspirating radiation shield for temperature and humidity sensors. • DB-9 serial computer connection (location to be determined). • WeatherMaster 2000 software (includes Cameo/Aloha interface). 20.03 1 Interface weather station to computer network with RS232 to Ethernet adapter, LDV 19110180 (or current model). 20.04 1 Garmin StreetPilot 7200 (or current model) Pre -Loaded Auto -routing Voice Guidance GPS, includes roof mounted antenna GA27C (or current model). Product features: • 7-inch touch -screen display • Preloaded with City Navigator NT detailed maps and display navigation • Automatic route calculation; voice -prompted, turn -by -turn directions; 2D or 3D map view • Alphanumeric remote control. 20.05 3 Franklin Instruments #FD254-I00-0P4 (or current model) clocks with 2.5" LED display and 12 hour or 24 hour modes. 20.06 1 Intellitec Emergency Time Manager, #00-00775-000 (or current model) clock and timer with the following functions: • Time of day in hours and minutes. • Sweep second hand. • Elapsed time in hours and minutes. • 4 alarm timers in 1, 2, 5 and 10 minute increments. Miami PO 22' 1-12-07 MRS.xls 15 1/12/2007 LDEMI LDV, Inc. +. 180 Indus7ial Drive IMO �i Burlington, WI 53105 ow 800.558.5986 �Vine �� Fax 262.763.0156 V www.ldvusa.com Section Qty 20.07 1 Middle Atlantic Products, Inc. MRK-4026 (or current model) forty -space 19" wide x 26.5" depth (24" useable depth) open framed electronics equipment rack with caster base, located as shown on drawing. Rack will slide out from its fixed position to allow side access to rack equipment. 20,08 1 Middle Atlantic MW-4FT top fan panel, with two (2) 50 cfm ventilation fans, QFAN. 20.09 1 Middle Atlantic VFD-40 vented front door with key lock. 20.10 1 Middle Atlantic PD-1020C-NS (or current model) 20 amp power strip with 5 duplex outlets. 21.00 RADIO INTEROPERABILITY SYSTEM: 21.01 1 Raytheon JPS ACU-1000 Wide Area Interoperability System (WAIS) Equipment Bundle. Includes: • ACU-1000 card cage • PSM-IA power supply module • CPM-4 control processor module • HSP-2 handset speaker module • Control Site Software (to be loaded on a remote PC by customer) • Operation Manual 21.02 10 DSP-2 Radio Interface Module (one per radio). 21.03 2 PSTN-1 Telephone Interface Module (one per telephone line). 21.04 10 Cable to interface radio to radio interoperability system. 21.05 Two (2) days of training for up to ten (10) people on ,IPS ACU-1000 radio interoperability system provided by Raytheon representative at customer's location. 22.00 EXTERIOR STORAGE COMPARTMENTS: 22.01 1 Single door underbody storage compartment with approximate interior dimensions 15" high x up to 24" wide x 25" deep constructed from 0.125" aluminum with all welded seams. 22.02 1 Single door underbody storage compartment with approximate interior dimensions 15" high x up to 36" wide x 25" deep constructed from 0.125" aluminum with all welded seams. 22.03 Compartments will be constructed to the following specifications: • Sweep out type bottoms with 1/2" drain holes. • 2" box pan doors and door frames fabricated from 0.125" aluminum. • Door frames shall be riveted to the body and welded to the compartments. • Compartments shall have a dome light that illuminates when the door is opened. • Compartments shall have dri-deck material install with tapered front Hp. Compartment doors will be constructed to the following specifications: • Stainless steel hinges attached with stainless machine screws. • Slam latches and flush mounted handles. • 0.100" bright polished aluminum diamond plate on interior surfaces fastened with stainless hardware. • All horizontally hinged doors shall be held open in a 120° position with gas charged lift/support cylinders. • All doors shall be sealed with industrial grade neoprene gasket. 23.00 AWNING: 23.01 1 Carefree ONE -Touch 20' electric awning with the following features: • Sunbrella solution -dyed acrylic fiber fabric, 4630 Cadet Grey (other colors available on request). • 12Vdc operation through mounted control panel, contains three manual overrides if power is lost. • Aluminum slatted wrap around cover. • Plastic roller on body door corner to prevent awning damage. • WindSmart Automatic Wind Sensor, closes awning automatically in high wind conditions. 24.00 OBSERVATION DECK AND LADDER: Miami PD 22' 1-12-07 MRS.xls 16 1/12/2007 LQV, Inc. =*' 180lndustrial Drive VM� sat Burlington, WI 53105 mom �p 800,558.5986 ���- Fox 262,763.0156 www.ldvusa.com Section Qty 24.01 1 15" wide roof access ladder on the rear of the vehicle, constructed using 1" dia. X 0.083" brush finished tubular aluminum rails and aluminum grip strut rungs. Rungs shall be welded to the rails for maximum strength. 24.02 1 5-ft. long x 6.5-ft, wide (approx. dims.) OSHA compliant collapsible observation deck railing. Railing is 42" high in extended position and is fabricated from 1" sq. x 0.125" brush finished tubular aluminum with stainless steel hinges and stainless steel quick -release pins. 25.00 LEVELING SYSTEM: 25.01 1 Heavy-duty Quadra MFG. Inc. Big FootTM model QE-2 four point fully automatic one -touch leveling system. Includes: • 17,000-Ib. capacity 24" jack with 18" stroke (4 total) • Air ride dump valve • Fully automatic control panel with manual feature • Safety interlock when jacks are deployed 25.02 1 High density polypropylene, injection molded yellow colored Super Dolly Pads for use with leveling system jacks. Pads measure 15" x 17" x 1" thick with a grab strap an one side (set of 4). _ 26.00 MISCELLANEOUS OPTIONS: 26.01 1 Removable Quartet Magnetic Porcelain Marker Board QRT P563T (or current model) 36" x 24". • White, magnetic; matte finish for reduced glare, • Full-size tray for markers and erasers. • Brackets on the exterior of the vehicle. 26,02 1 Heavy-duty zippered storage bag for exterior shelf or dry erase board. 26.03 2 Kidde Pro Line 3-A: 40-B: C 5 pound dry chemical fire extinguishers. 26.04 3 First Alert 9-volt combination Carbon Monoxide and Smoke alarms. 27.00 LDV MANUALS. 27.01 1 Complete manual set on CD, including the following: • As -built specifications with interior and exterior drawings as used for production of the vehicle. • Chassis and body owner's manuals. • All individual component manuals and warranty registration cards as provided by component manufacturers. Customer is responsible for completing warranty cards and mailing them to manufacturers. • LDV 12Vdc and 120Vac legends showing wire gauge, color, number and function. • LDV 12Vdc high current wiring diagram illustrating the battery system, isolators, power converters, alternator, disconnect switches and control panels. • LDV roof top antenna placement drawing and legend identifying antenna placements and termination points. • LDV AudioNideo cabling diagram. • LDV Telephone system punch block wiring diagrams. • LDV Alarm system zones legend. • LDV warranty and Return Authorization procedures. • Chassis and generator maintenance and service logs. • Battery maintenance information. 28.00 MISCELLANEOUS: 28.01 1 Set of Freightliner chassis parts and service manuals. 28.02 1 Cummins engine and Allison transmission parts and service manuals. 28.03 1 Set of generator parts and service manuals. Mlaml PD 22' 1-12-07 MRS.xls 17 1/12/2007 LOViNmilumrigt �1 Section 28.04 28.05 Qty LDV, Inc. 180 Industrial Drive Burlington, WI 53105 800.558,598o Fax 262.763.0156 www.ldvusa.com At time of delivery to customers facility an LDV representative will provide up to eight (8) hours of orientation on LDV installed systems, as applicable: • Generator start up and shut down procedure • Leveling system operation • AC and DC electrical systems operation • HVAC systems operation • Mast operation • AudioNideo system operation, does not include programming VCR's, TV's, etc. • Alarm operation • Awning operation Note: LDV project scope does not include certain tasks or costs that are the responsibility of the customer unless clearly specified as LDV supplied. These items include, but are not limited to: • Radio and telephone system programming. • Activation and service fees for cellular telephones, satellite telephones, satellite TV, satellite Internet access. • Loading and configuring computer software. In the event of a discrepancy between the drawing and specification, the specification will supersede. LDV reserves the right to make substitutions of equal quality and specifications of those listed in this document. Miaml PD 22' 1-12-07 MRS.xls 18 1/12/2007 LOV...it Pricing Pane:. THIS QUOTE IS ONLY A VERY PRELIMINARY BALLPARK PRICE. A PURCHASE ORDER CAN NOT BE ISSUED AGAINST THIS QUOTE Total commercial price as specified, continental US Payment terms: Net 30 Commercial delivery terms: 12 months or less ARO Quoted price does not include any applicable FET, federal, state or local tax unless specified LDV, Inc. 180 Industrial Drive Burlington, WI 53105 800.558.5986 Fax 262.763.0156 www.ldvusa.com $ 469,138.00