HomeMy WebLinkAboutMaterial Safety Data Sheet 414SDS-POWF'.1'LOCK
Page 1 of 1
MATERIAL SAFETY DATA SHEET
FOR COATINGS, RESINS, AND RELATED MATERIALS
REPLACES NPCA 1-82
Manufactured for
AMERICAN COATINGS CORPORATION
3037 NW 60th STREET
FT. LAUDERDALE, FL 33309
(954)970-7820
DATE OF PREPARATION
April 19, 2002
EMERGENCY TELEPHONE
(800) 533-0151
SECTION I - PRODUCT INFORMATION
PRODUCT NAME: POWERLOCK )
PRODUCT DESCRIPTION: Lock Down Encapsulant
Penetrating Encapsulant
Removal Encapsulant
PRODUCT CLASS: Copolymer Latex Coating - Water Dispersion
TRANSPORTATION INFORMATION: Shipping Class 55, Paint (No special labels required.)
SECTION II HAZARDOUS
S INGREDIENTS-:`
INGREDIENT.
Polymerized Latex Emulsion
19011-09-03
OCCUPATIONAL
EXPOSURE LIMIT
Percent TLV PEL
N/E N/E
VAPOR
PRESSURE
The components of this mixture are not designated :carcinogenic by the National Toxicology
Program (NTP) or the International Agency for Research or_Cancer (IARC).
SECTION ID - PHYSICAL DATA
SOILING RANGE: 212° F VAPOR DENSITY: Lighter than air
EVAPORATION RATE: Slower than ether VOLATILE VOLUME: 88% - 96%
WT/GAL: 8.75 Ibs SPECIFIC GRAVITY: 1.05
SOLUBILITY IN WATER: Appreciable VISCOSITY: Approx. 40 cps
DECOMPOSITION TEMPERATURE: Approx. 240°F (115° C) FREEZING POINT: 32° F (0° C)
MSDS-POWERtOCK
Page 2 of 2
SECTION 1V - FIRE AND EXPLOSION HAZARD DATA
FL MN_ S,ILITY CLASSIFICATION:
OSi-IA - IIIB DOT - Not Regulated
LEL Not available
FLASH POINT - No flash to boiling.212° F (TCC)'
EXTINGUISHING MEDIA:
X Foam X Alcohol Foam X CO2 X Dry Chemical X Water Fog' Other
UNUSUAL FIRE AND EXPLOSION HAZARDS: None known
SPECIAL FIREFIGHTING PROCEDURE: Product will not burn until water has evaporated. For
dried•film or residual solids, full protective equipment is recommended, including
self-contained breathing apparatus.
SECTION V - HEALTH HAZARDS
• EFFECTS OF OVEREXPOSURE: A TLV for this mixture has not been established.
Eye contact may cause moderate irritation: Prolonged skin contact may cause slight
3.rx.itati_on._ .E.posu_to concentrated vapors may cause some individuals to experience
headaches or -dizziness. Ingestion of the liquid may irritate the mucous'membranes and
gastrointestinal tract and may cause vomiting.
if headaches or dizziness are experienced by an individual, the product handling
procedures and workplace ventilation should be examined.
MEDICAL CONDITIONS PRONE TO AGGRAVATION .BY EXPOSURE: No available information.
•
PRIMARY ROUTES OF ENTRY: Dermal, Inhalation
EMERGENCY AND FIRST AID PROCEDURE: Skin - wash with soaP and water. Eyes - flush with
clean water at least 15 minutes, If irritation persists, consult physician.
Inhalation - remove to,fresh air. If breathing is difficult, administer oxygen.. If
irritation persists, consult physician. Ingestion - give two glasses of Water, induce.
•vomiting, consult physician or poison control center'. Never give anything by mouth to
an unconscious person.
SECTION VI - REACTIVITY DATA
STABILITY: Stable HAZARDOUS POLYMERIZATION: Will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition will yield CO, CO2, AND HC1.
)NDITIONS TO AVOID:
t!
None known.
INCOMPATIBILITY {Materials to Avoid):
Materials incompatible with water and strong oxidizers.
MSDS-POWEPLOCK Page 3 of 3
SECTION VII - SPILL OR LEAK PROCEDURES
.,CEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLE=: Majcr spills should be
collected for disposal. Minor spills may be flushed cc sewer if regulations permit.
Before drying, product may be washed away with water; after drying, remove with a
paint scraper or strong solvent.
WASTE DISPOSAL METHOD: In accordance with all applicable regulations. Review hazard
section of this sheet before attempting clean-up. Empty containers are non -hazardous
- under RCRA as industrial waste.'
SECTION VIII - SAFE HANDLING AND USE INFORMATION
RESPIRATORY PROTECTION: In restricted ventilation areas, of applications where mists or
spray may be generated, avoid inhalation of airborne particulates by using an approved
respirator with organic vapor cartridge with prefilter for mist or dust.
VENTILATION: General (mechanical) room ventilation is expected to be satisfactory. Local
exhausts should be considered for coating operations.
PROTECTIVE GLOVES: Impervious gloves.
-YE PROTECTION: Goggles; faceshields, or other eyewear to protect from splash. As'a.
general rule, contact lens should not be worn when working with chemicals.
OTHER PROTECTIVE EQUIPMENT: None.
HYGIENIC PRACTICES: Thoroughly cleanse hands after handling. Launder contaminated
clothing before reuse.
SECTION IX - SPECIAL PRECAUTIONS
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Avoid breathing vapors. Avoid
application to hot surfaces, as vapors may be'irritating. Keep container closed.
Use with adequate ventilation. Store indoors at temperatures of 45°F - 90°F. Do not
'store in contact with iron, aluminum, zinc, copper, or other alloys.
OTHER PRECAUTIONS: For industrial/professional use only. Not intended for retail sale
or use by individual consumers. Do not reuse container for potables or edibles.