HomeMy WebLinkAboutFreightliner SpecificationsFREIGHTLINER
SPECIFICATIONS
BERGKAMP INC.
FP 5 "TOTAL PACKAGE" FLAMELESS POTHOLE PATCHER
SPECIFICATIONS
CAPACITIES
Hopper Size, cu. yds. (cu. m.)
Typical load size, tons
Hydraulic Oil Tank, gal. (L)
Cleaning Fluid Tank, gal. (l.)
Tack Oil Tank, gal. (l.)
Air Tank, gal. (l.)
Water Tank, gal.(1.)
MEASUREMENT, BASE UNIT WITHOUT OPTIONS
Length, in. (m.)
Overall Width, Mounted, in. (m.)
Overall Width, Shipping, in. (m,)
Height, Above Truck Frame, in. (m.)
Height, Shipping, in. (m.)
Weight, Empty, lb. (kg.)
TRUCK REQUIREMENTS
Axles
Useable Cab -to -Axle, in. (m.)
Useable Cab -to -End -of -Frame, in, (m.)
Front Axle, lb. (kg.)
Rear Axle, lb. (kg.)
GVW, minimum, lb. (kg.)
Air Brakes
Air Compressor
Transmission
Clutch Brake
Due to variances in curb weights between truck models, alternate axle capacities may be
required. Bergkamp should be consulted regarding specifications of customer supplied trucks.
PATCHING MIX HOPPER SYSTEM
50° side slopes, 90° end slopes, with 2-inch (5 cm) industrial
insulation encased in a double steel jacket, and temperature gauge.
5.1 (3.9)
6.0
25 (95)
15 (57)
80 (303)
19 (72)
15 (57)
180 (4.57)
96 (2.44)
87 (2.20)
60 (1.52)
64 (1.66)
7800 (3538)
Hopper
2
124 (3.15)
155 (3.93)
11,000 (4,990)
22,000 (9,979)
33,000 (14,969)
Recommended
Required (maximum available)
PTO Provisions
Recommended
specsAp4.112
Page 1 of 5
rev111292
Feed 6 x 6 screw conveyor, hydraulically driven, reversible with control
at operator work station. Extra auger torque for very stiff mixes,
like cold mix, is provided by shifting a selector valve at the
operator's station.
Agitator Full hopper length, hydraulically driven, reversible with control at
operator work station.
Chute Pivots 90° for distribution of patching mix from Hopper Pan
Shoveling pan below the discharge of the auger for easy shoveling
of the patching mix.
HYDRAULIC STEEL HOPPER DOORS
Power Source Unit's auxiliary hydraulic system.
Doors Hydraulically operated, double jacketed with 2-in. (5 cm.)
insulation.
Control Valve Manually operated three position hydraulic control valves.
HYDRAULIC SYSTEM
Reservoir Steel, 25 gallons. Tank is equipped with:
- Oil level sight gauge
- Filter breather cap
- Shutoff valve on the external suction line from tank. Valve is to
be located as close to the tank as possible. If return line is located
in any position other than on top of tank, a second valve is to be
installed in the return line near the tank.
- Fluid filter to be located outside of tank on the external return
line.
PTO
Pump
Hoses
To match customer truck, minimum 21 hp (15.75 kw) with off -on
cab control.
Variable volume piston pump; single stage, direct mounted to a
heavy-duty clutched drive single speed PTO.
Rated 3000 psi (212 kg/cm2)
Throttle Control Automatic truck engine throttle control provides correct hydraulic
flow on demand.
Control Valves Multi -spool control valves for hopper auger and agitator, and
auxiliary tools, with built-in adjustable relief.
specs/1p4.112
Page 2 of 5
rev111292
Auxiliary Circuit
(Hand Tools)
With quick coupling attachment and controls located at operator
work station.
Secondary Auger
Motor (optional)
Matches Primary motor in hp and torque to produce double the hp
and torque in parallel mode. Auger powered by 14.9 hp motors
producing 15,600 in # of torque.
HEATING SYSTEMS
Working hours
power source electric; minimum 230 volt, 43
amp hydraulically driven AC generator
After hours power
Source electric; minimum 230 volt, 43 amp customer supplied
Hopper heater minimum 2 each, 230 volt, minimum 3.5 kw electric heater
element
Heater thermostatic
controller 230 volt, displays setpoint and hopper temperature with fail
safe off mode to prevent overheating of materials.
200,000 BTU with shut-off valve and 10 ft. of hose, with torch
hose storage
Hand Torch
(option)
Electrical
protection
Troubleshooting
aide
Tack oil tank
- hopper heater; 40 amp ground fault interrupt breaker that trips at
5 milliamperes or less for worker safety - tack tank and system controls; 15 amp, ground fault interrupt
breaker that trips at 5 milliamperes or less for worker safety
onboard voltage and amperage meters
230 volt, thermostatically controlled, minimum 800 watt silicone
drum heat band. No direct contact with the tack oil. Located at the
bottom of the tank.
TACK COAT SYSTEM
Air Supply provided by truck's air compressor (Has no effect on the truck
warrant ).
specs/1p4.112
Page 3 of 5
rev111292
Air Tank
Tack Coat Tank
Hose and
Spray Wand
ASME approved, with bleed and isolation valves and pressure
gauge.
- Minimum 70 psi tractor protection valve. (No air can be taken
from the truck system unless the pressure is above 70 psi to
provide adequate pressure for the truck braking system).
Tank to be mounted on the machine
ASME approved
- insulated with 2 inches (5 cm) R12 insulation.
- Opening in top is 6 x 12 inches for ease of filling, visual
inspection of contents, and tank level.
To help clean out and tack coat potholes; 12 ft (3.66
m) of hose. Dual feed of air and tack material, plumbed so air
cleans out spray nozzle, pushes tacking material from wand and
hose into supply tank and stirs supply tank. Tack coat line has off-
on valve. Storage provided.
SPOILS BINS
Rear Mount 0.64 cu. yd. (0.5 cu. m.), gravity dump.
Side Mount 0.55 cu. yd. (0.42 cu. m.), gravity dump.
PAVEMENT BREAKER SYSTEM (Standard)
Power Source Unit's auxiliary hydraulic system.
Hammers 45 pound (20 kg) hydraulically powered with asphalt chisel and 25
ft. (7.6 m.) of hose with quick couplings. (An optional 67 pound
(30 kg) hydraulically powered with asphalt chisel and 25 ft. (7.6
m.) of hose with quick couplings is also available).
Hose Reel Spring loaded.
Storage Hand rack for hose and separate storage for breaker.
COMPACTOR SYSTEM
Compactor Vibratory type, 5 hp (3 kw.) gas engine, 2475 lbs. (1123 kg.) force,
plate size 19 x 21 in. (48 x 53 cm.), weight 1961bs. (89 kg.)
Water Tank 15 gal. (57 l.) gravity feed with filler cap, tank isolation valve and
hose.
Platform Hydraulic with control valve, pavement breaker mount.
specs/p4.112
Page 4 of 5
rev111292
CLEANING FLUID SYSTEM (Cleans tools, sprays down mix hopper)
Tank 15 gallon (57 1.) with vented fill cap and tank isolation valve.
Pump 12 volt DC.
Hose and 12 ft. (3.66 m) of hose with off -on valve and storage.
Spray Wand
Other Plumbed into tack coat system for flushing of line and spray wand.
SAFETY LIGHTING AND ALARMS
Strobe * 12 volt DC; flashing, amber color.
Directional * 12 volt DC with cab controls for off -on and patterns of left
Arrow Board left arrow, right arrow, both arrows, and flasher bar.
Back Up Alarm Electronic type.
* System available for use with 24 volt DC supply.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
specsltp4.1 i 2
Page 5 of 5
revi55292